IC693PWR330

GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

IC693PWR330 Image

IC693PWR330

  • Availability: In Stock Ships Today!
  • Units in Stock: Immediate Availablity: 94 Units!
  • Call for best Pricing+ 1 919 680 1773
  • Manufacturer: GE-IP
  • Description: 120/240 Vac 125 Vdc High capacity PS
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693PWR330 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z,

Product Manual Excerpt

IC693PWR330 High Capacity Power Supply, 120/240 VAC/125 VDC Input The IC693PWR330 High Capacity Power Supply is rated for 30 watts output. For applications requiring greater +5V current capacity than is available with the standard supply (IC693PWR321), this supply allows all 30 watts to be consumed from the +5V supply. It can operate from an input voltage source in the range of 85 to 264 VAC or 100 to 300 VDC. This power supply provides the following outputs: +5 VDC output. +24 VDC Relay power output which provides power to circuits on Series 90-30 Output Relay modules. Isolated +24 VDC, which is used internally by some modules, can also be used to provide external power for 24 VDC Input modules. The load capacity for each output of this power supply is shown in the following table. Table 4-4. IC693PWR330 Power Supply Capacities Catalog Number Load Capacity Nominal Input Output Capacities (Voltage/Power ) IC693PWR330 30 Watts 100 to 240 VAC or 125 VDC +5 VDC 30 watts +24 VDC Isolated 20 watts +24 VDC Relay 15 watts Total of all outputs combined cannot exceed 30 watts. 100-240 VAC PROGRAMMABLE CONTROLLER SYSTEM STATUS INDICATORS a45625 + PWR OK RUN BATT BATT E R LITHIUM Y BACK UP BATTERY BATTERY CONNECTOR RS 485 COMPATIBLE SERIAL PORT CONNECTIONS FOR AC/DC POWER SOURCE INTERNAL POWER SOURCE FOR MODULES REQUIRING 24VDC IC693PWR330 GE Fanuc Series 90-30 POWER SUPPLY 50/60 HZ 100VA 125VDC, 50W INPUT 24 VDC OUTPUT 0.8A MAX. HIGH CAPACITY Figure 4-2. High Capacity AC/DC Input Power Supply - IC693PWR330 Series 90 30 Power Supplies 4 GFK 0898F Chapter 4 Series 90 30 Power Supplies 4-5 Table 4-5. Specifications for IC693PWR330 High Capacity AC/DC Input Power Supply Nominal Rated Voltage Input Voltage Range AC DC 120/240 VAC or 125 VDC 85 to 264 VAC 100 to 300 VDC Input Power (Maximum with Full Load) 100 VA with VAC Input 50 W with VDC Input Inrush Current 4A peak, 250 ms maximum Output Power 5 VDC: 30 watts maximum 24 VDC Relay: 15 watts maximum 24 VDC Isolated: 20 watts maximum NOTE: 30 watts maximum total (all three outputs) Output Voltage 5 VDC: 5.0 VDC to 5.2 VDC (5.1 VDC nominal) 24 VDC Relay: 24 to 28 VDC 24 VDC Isolated: 21.5 VDC to 28 VDC Protective Limits Overvoltage: Overcurrent: 5 VDC output: 6.4 to 7 V 5 VDC output: 7 A maximum Ride Through Time: 20 ms minimum Field Wiring Connections for the AC/DC Input Power Supplies The two AC/DC input power supplies have six terminals for user connections. These connections are described below. AC Power Source Connections The Hot, Neutral, and Ground wires from the 120 VAC power source or L1, L2, and Ground wires from the 240 VAC power source connect to the system through the top three terminals of the terminal strip on the front of the power supply. DC Power Source Connections Connect the + and wires from the 125 VDC (nominal) power source to the top two terminals on the terminal connector. These connections are not polarity-sensitive on an AC/DC input power supply; however, for systems with more than one baseplate, the input wiring polarity must be consistent (see the section DC Power Source Connections in Chapter 2 for details on this). NOTE: The DC Input-only type supplies, which are discussed later in this chapter, are polarity sensitive. Input Overvoltage Protection Devices This information applies to all Series 90-30 power supplies that have six terminal boards. The overvoltage protection devices for this power supply are connected internally to pin 4 on the user terminal strip. This pin is normally connected to frame ground (pin 3) with the supplied jumper strap which is installed at the factory. If overvoltage protection is not required or is supplied upstream, this feature can be disabled by removing the jumper strap from pins 3 and 4. If you want to Hi-pot test this supply, overvoltage protection must be disabled during the test by removing the terminal strip jumper strap. Re-enable overvoltage protection after testing by reinstalling the strap. 4 4-6 Series 90 30 PLC I/O Module Specifications July 2000 GFK 0898F 1 2 3 4 a47106 Jumper Strap Connects Overvoltage Protection Devices to Frame Ground Screw Terminals on Terminal Board Frame Ground Figure 4-3. Overvoltage Protection Devices and Jumper Strap Isolated 24 VDC Supply Output Connections The bottom two terminals of the power supply terminal strip provide connections to the Isolated +24 volt DC output which can be used to provide power for external circuits (within power limitations of the supply). Caution If the Isolated 24 VDC supply is overloaded or shorted, the Programmable Logic Controller will stop operation. Series 90 30 Power Supplies 4 GFK 0898F Chapter 4 Series 90 30 Power Supplies 4-7 DC Input Only Power Supplies IC693PWR322 Standard Power Supply, 24/48 VDC Input The IC693PWR322 is a 30 watt output power supply designed for 24 VDC or 48 VDC nominal inputs. It will accept an input voltage range from 18 VDC to 56 VDC. Although it is capable of maintaining all outputs within specifications with input voltages as low as 18 VDC, it will not start with initial input voltages of less than 21 VDC. This power supply provides the following outputs: +5 VDC output. +24 VDC Relay power output which provides power to circuits on Series 90-30 Output Relay modules. Isolated +24 VDC, which is used internally by some modules, can also be used to provide external power for 24 VDC Input modules. The load capacity for each output of this power supply is shown in the following table. Table 4-6. IC693PWR322 Power Supply Capacities Catalog Number Load Capacity Input Output Capacities (Voltage/Power ) IC693PWR322 30 Watts 24 or 48 VDC +5 VDC 15 watts +24 VDC Isolated 20 watts +24 VDC Relay 15 watts Total of all outputs combined cannot exceed 30 watts. SYSTEM STATUS INDICATORS a44854 + PWR OK RUN BATT BATT E R LITHIUM Y BACK UP BATTERY BATTERY CONNECTOR RS 485 COMPATIBLE SERIAL PORT CONNECTIONS FOR DC POWER SOURCE INTERNAL POWER SOURCE FOR MODULES REQUIRING 24VDC IC693PWR322 + GE Fanuc Series 90-30 PROGRAMMABLE STANDARD POWER SUPPLY CONTROLLER 24 VDC OUTPUT 0.8A MAX. INPUT 24/48 VDC 50 WATT PROGRAMMABLE CONTROLLER Figure 4-4. Series 90-30 24/48 VDC Input Power Supply - IC693PWR322 4 4-8 Series 90 30 PLC I/O Module Specifications July 2000 GFK 0898F Table 4-7. Specifications for IC693PWR322 Power Supply Nominal Rated Voltage Input Voltage Range Start Run 24 or 48 VDC 21 to 56 VDC 18 to 56 VDC Input Power 50 watts maximum at full load Inrush Current 4A peak, 100 ms maximum Output Power 5 VDC: 15 watts maximum 24 VDC Relay: 15 watts maximum 24 VDC Isolated: 20 watts maximum NOTE: 30 watts maximum total (all three outputs) Output Voltage 5 VDC: 5.0 VDC to 5.2 VDC (5.1 VDC nominal) 24 VDC Relay: 24 to 28 VDC 24 VDC Isolated: 21.5 VDC to 28 VDC Protective Limits Overvoltage: Overcurrent; 5 VDC output: 6.4 to 7 V 5 VDC output: 4 A maximum Holdup Time: 14 ms minimum Standards Refer to data sheet, GFK-0867B, or later version for product standards, and general specifications. Calculating Input Power Requirements for IC693PWR322 The following graph is a typical 24/48 VDC power supply efficiency curve. A basic procedure for determining efficiency of the 24/48 VDC power supply follows the figure. 5 10 15 25 30 AVERAGE INPUT POWER (WATTS) TOTAL OUTPUT POWER (WATTS) a44963 50 20 10 20 30 40 45W Figure 4-5. Typical Efficiency Curve for 24/48 VDC Power Supply Note Start-up surge at full load is 4 amps for 250 milliseconds (maximum). Series 90 30 Power Supplies 4 GFK 0898F Chapter 4 Series 90 30 Power Supplies 4-9 Input Power/Current Calculation Determine total output load from typical specifications listed for individual modules in Chapters 2 and 3. Use the graph to determine average input power. Divide the input power by the operating source voltage t