GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

IC693MDL655 Image


Same Day - Free Shipping

  • Manufacturer: GE-IP
  • Description: Neg/Pos Logic, 1 ms, (32 pts), 24 Vdc Input
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693MDL655 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z,

Product Manual Excerpt

24 VDC Positive/Negative Logic, 32 Point Input IC693MDL655 The 24 volt DC Positive/Negative Logic Input module for the Series 90-30 Programmable Logic Controller provides 32 discrete input points. The inputs are arranged in four isolated groups of eight (A1 - A8, B1 - B8, C1 - C8, and D1 - D8); each group has its own common. The inputs are positive or negative logic inputs and will operate at levels up to 30V. Backplane isolation between the field side and logic side is provided by opto-couplers on the module. Isolation is also provided between the four groups of inputs on the module, however each group of eight inputs is referenced to the same user common connection. There are no special fault or alarm diagnostics reported. LED indicators (labeled A1 - A8, B1 - B8, C1 - C8, D1 - D8) at the top of the module provide the ON/OFF status of each input point. This module is configured as a 32-point input type and uses 32 bits of discrete %I input data. Current into an input point results in a logic 1 in the input status table. Power to operate field devices can be supplied by the user, or from the isolated +24 VDC supply available at the module s I/O connectors. This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC system. Connections to the input circuits are made from the user s input devices to two male (pin-type) 24-pin connectors (Fujitsu FCN-365P024-AU) mounted on the front of the module. The connector mounted on the right of the module (front view) interfaces with groups A and B. The connector on the left side of the module interfaces with groups C and D. Wiring from the module s connectors to field devices is made through a cable having a mating female connector on one end and stripped and tinned wires on the other end. You can purchase a pair of pre-wired cables, catalog numbers IC693CBL327 and IC693CBL328 or, if required for your application, build your own cable. Refer to Building Cables for 24-Pin Connectors in the IC693CBL327/328 data sheet in Appendix C of this manual for more information. Discrete Input Modules 6 GFK-0898F Chapter 6 Discrete Input Modules 6-27 Table 6-12. Specifications for IC693MDL655 Rated Voltage 24 volts DC, Positive or Negative Logic Input Voltage Range 0 to 30 volts DC Inputs per Module 32 (four groups of eight inputs each) Isolation 1500 volts between field side and logic side 250 volts between groups Input Current 7.0 mA (typical ON current @ 24 VDC) Input Characteristics On-state Voltage 11.5 to 30 volts DC Off-state Voltage 0 to 5 volts DC On-state Current 3.2 mA (minimum) Off-state Current 1.1 mA (maximum) On response Time 2 ms maximum Off response Time 2 ms maximum Internal Power Consumption 195 mA (maximum) from +5V bus on backplane; (29 mA +0.5 mA/point ON +4.7 mA/LED ON) 224 mA (typical) from isolated +24V bus on backplane or from user input supply @ 24 VDC and all 32 inputs ON) Maximum number of inputs ON is dependent on ambient temperature as shown in the figure below. Refer to data sheet GFK-0867F (or later revision) for product standards and general specifications. 10 C 20 C 30 C 50 C 60 C NUMBER OF INPUTS/GROUP ON AMBIENT TEMPERATURE ( C) a45137 40 C 24V SUPPLY 30V SUPPLY 8 6 4 2 4 INPUTS PER GROUP ON 35 C 3 INPUTS PER GROUP ON Figure 6-19. Input Points vs. Temperature for IC694MDL655 6 6-28 Series 90-30 PLC I/O Module Specifications July 2000 GFK-0898F IC693MDL655 Input Module Field Wiring Information The following two figures provide wiring information for connecting user supplied input devices and power source to the 24 volt DC (TTL) positive/negative logic input module. The first figure shows a typical input circuit. The second figure shows how field devices are connected to the module. 0.5W 3.3K 820 INPUT COMMON 5V 5V 0V 56K 10K a45038 0V ICS MODE 1 MODE 0 0V LED 680 0.01 0.22 μf Module point numbers in the following figure are shown in bold text. B2 +24V a45037 * BACKPLANE ISOLATED +24V SUPPLY MAY BE USED IN LIEU OF EXTERNAL USER SUPPLY A5 A3 B2 B4 B6 B8 A7 A1 B12 B11 B10 B9 B8 B7 B6 B1 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 B5 B4 B3 NC ACOM +24V (OUT) NC A2 A4 A6 A8 BCOM B7 B5 B3 B1 0V NC NC * * I/O CONN (AB) D5 D3 C2 C4 C6 C8 D7 D1 A1 A2 A3 A4 A5 A6 A7 A12 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 A8 A9 A10 A11 NC DCOM (OUT) NC D2 D4 D6 D8 CCOM C7 C5 C3 C1 NC 0V NC * * I/O CONN (CD) = FUJITSU CONNECTOR PINS A1 A12, B1 B12 MODULE POINT NUMBERS ARE SHOWN IN BOLD TEXT. Figure 6-20. Field Wiring 24 Volt DC Positive/Negative Logic 32-Point Input Module - IC693MDL655 Discrete Input Modules 6 GFK-0898F Chapter 6 Discrete Input Modules 6-29 Field Wiring Work Sheet for IC693MDL655 The following table is provided for the convenience of our customers as an aid to wiring the 24-pin connectors using cable IC693CBL315. It includes all of the required wiring information in one table. This table has the following information: module point number: A1 - A8, B1 - B8, C1 - C8, D1 - D8, voltage and common points connector pin number: A1 through A12, and B1 through B12 cable pair number: pair 1 through pair 12 wire color code: base color or base color with tracer color Columns are also provided for circuit references and customer wire numbers. Please copy and use the work sheets on this and the following page as needed when wiring the 24 VDC Positive/Negative Logic, 32 Point Input module. Wiring for Module Groups A and B (connector on right front of module)

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.

UPS Ground shipping is always FREE!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PDF Electric & Supply 3-year warranty.

UPS Ground shipping is always FREE!

What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Electric & Supply packaging and includes a PDF Electric & Supply 3 Year Warranty.

UPS Ground shipping is always FREE!

What is Reconditioned?

Reconditioned products from PDF Electric & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.

Our Reconditioned Products always come with a PDF Electric & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!

Repair Service

3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.