GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

IC693CPU363 Image


Same Day - Free Shipping

  • Manufacturer: GE-IP
  • Description: GE Fanuc Series 90-30 CPU Module with serial ports
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693CPU363 : -AB, -AC, -AD, -BD, -BE, -BF, -BG, -BH, -CJ, -DJ, -DK,

Product Manual Excerpt

The Model 350 and 360 CPU operating firmware is stored in FLASH memory. The firmware upgrade is provided on a floppy disk and must be serially downloaded from a Personal Computer. An IBM AT personal computer or better PC with a minimum 640K of RAM, one 3.5 floppy drive, MS-DOS version 3.3 or later (or Windows 95 or later), a hard drive, and one RS-232 serial port is required. In addition, a serial cable and RS- 232/RS-485 converter are required. The following serial cable/converter kit is available from GE Fanuc: IC690ACC901 Mini Converter (RS-232/RS-485) Kit with serial cable Functional Compatibility CIMPLICTY Machine Edition PLC Logic Developer version 2.11 or later, or VersaPro version 1.1 or later is required to utilize the features introduced in release 10.00 firmware. PLC Logic Developer, VersaPro version 2.00 or later, or Control software version 2.00 or later is required for C programming. Version 4.00 or later of the C toolkit must be used for C programming. Control software version 2.00 or later must be used to take advantage of Sequential Function Chart (SFC) subroutines. Logicmaster software version 9.02 or later must be used to take advantage of the features introduced in firmware release 9.00. Important Product Information 3 GFK-1512M Operating Notes User Information Cleared when Upgrading Firmware User information, consisting of program, configuration, CPU ID (used for SNP communications), and status tables in RAM memory, will automatically be cleared if the CPU firmware in flash memory is changed. You will need to restore these if upgrading firmware. A recommended procedure is to first back up your user information from RAM memory to Flash memory. Then write your new firmware to Flash memory (firmware is stored in a different location in Flash memory than that used for storing user information such as program, configuration, etc.). Finally, write your user information back out of Flash into RAM memory. As an alternative, your user information (program, configuration, etc.) can be restored from a computer-based backup program folder using your PLC programming software. The SNP ID, if required, must be set separately using the programming software or the Hand-Held Programmer (HHP). Option Module Revision Requirements Ethernet Interface Module Compatibility. All IC693 Ethernet Interface (IC693CMM321) modules used with these CPUs should be updated to IC693CMM321 firmware release 1.10 or later. This is also a requirement of the TCP/IP Ethernet version of the MS-DOS programming software. During a Run Mode Store (Alt + S hot key combination) of a large program block (greater than 14 kilobytes), the Ethernet module may time out, causing communications to fail. Changing the Communications Window to Run-to-Completion mode, or storing the program in Stop mode, will allow the store to take place successfully. FBC Compatibility. FBC version 3 or later is required for these CPUs. Writing to Flash Using the Windows PLC Programming Software When writing very large programs to flash memory, it may be necessary to increase the Windows PLC programming software request timeout value to avoid receiving a request timeout message. An upper bound of 25 seconds is typically satisfactory Storing Large Configurations The IC693 PLC normally supports 20 DSM314 modules in a system. This number may be reduced by other modules in the system, such as APM and GBC modules. It may also be further reduced if using datagrams that read the reference or fault tables. If the configuration and user program are stored at the same time, the presence of either C blocks within the LD program, or a C logic program may also affect the number of DSM314 modules that may be included in a system. If the store fails, it may be possible to work around this problem by first storing the logic program and then storing the configuration on a separate store request. The number of modules supported may be further reduced by the size of CPU user memory. No Model Number Checking with DOS-based programmer The No Model Number Checking feature does not support storing a 311, 313, 321, 323 or 331 configuration to a Release 9.0 or later CPU. Simultaneous Load and Store When operating with multiple programmers attached, if a store operation is initiated by one programmer, while a load operation is already in progress, the load request will fail. Transition Tables are not cleared when the reference tables are cleared. The transition tables are not cleared upon clearing the reference tables through the programmer. 4 Important Product Information GFK-1512M Problems Resolved by this Firmware Release (10.60) CPU won t handle 11K byte smart module init file With the new version of Horner PBM and the new version of VersaPro, both of which create and expect an 11K byte init file, logic analyzer traces show that the data received from the SI30 on the module are incorrect. That is, the data coming across the backplane was corrupted. A LOAD or VERIFY of the configuration works properly, so it appears that the data within the PLC is correct. Load of large (>32K) DSM zip files fails Load greater than 32K through 364 (stored over SNP) Failed with the following station manager log. = log <<< Exception Log >>> Log initialized using valid RAM information Log last cleared 01-JAN-2000 03:32:49.7 Date Time Event Count Entry 01-JAN-2000 03:33:17.2 8H 21H 00H 0024H 0202H 0000H 0001H 0000H ->01-JAN-2000 03:33:25.9 8H 1H 00H 0008H 0000H 0097H 002eH 0000H Restrictions and Open Issues Timing Issue with ALG220/221 Modules May Result in Incorrect %AI Values Read by CPU A problem was found with the IC693ALG220/221F (and earlier versions) where the actual %AI values reported by the card may exhibit erratic behavior (versions F and earlier may show this problem; the problem was fixed in version G or later). Certain current or voltage levels within the input range applied to the card could cause the %AI values to report incorrectly. The problem stems from the use of particular optocouplers, which may exhibit timing issues with these CPU35x/36x modules. (NOTE: CPUs 341, 331, 321, 313, and 311 have not exhibited this problem.) The IC693 PLC will generate a fatal fault if a ladder containing DOIO function block calls to a smart module is repeatedly placed in RUN then STOP mode A problem was found with the CPU where a ladder containing a call to a DOIO function block would cause the PLC to run out of system memory. This is caused when the PLC transitions to run mode and back to stop mode several times. If the configuration is stored, the system memory will be freed, and the PLC will resume normal operation. IC693 PLC CPU may Develop Fatal Fault During Store of Folders with Large Configurations The IC693 PLC CPU may generate a fatal fault during a store of a folder with an especially large configuration. This may be made worse by storing a program and configuration at the same time, or by having datagrams from a programmer present during the store. PID Integral Contribution The PID Integral Contribution is not calculated correctly with an integral rate of 0 or 1. A CPU360 Configuration Stored to CPU352 may Cause Fatal Fault If a CPU360 configuration file is stored to a CPU352, the PLC may generate a fatal fault when transitioning to run mode. Reading from an Invalid Flash Part may Cause a Watch Dog Timeout If a corrupted flash part is read, the Watch Dog Timer on the PLC may be triggered. This can be fixed by completing a valid flash store. Important Product Information 5 GFK-1512M Fatal Fault Occurs when Configuring a Module with the HHP Following a Maximum Size PLC Store The IC693 PLC CPU may generate a fatal fault while attempting to configure a module with the Hand-Held Programmer (HHP) following a maximum size store to the PLC. Firmware Update Fail Following Power-up with Clear M/T and a Write to Flash Firmware update may fail following a power-up with Clear M/T pressed on the Hand-Held Programmer and a write to flash. Cycling power on the PLC will enable the upgrade to proceed. Documentation Instructions for using these two modules can be found in the latest version of the following manuals: Hardware Description, Installation Instructions: IC693 Installation and Hardware Manual General Configuration Instructions: IC693 PLC Programming Software User s Manual System Operation: IC693 PLC System Manual System Operation and Instruction Set: IC693 PLC Reference Manual 6 Important Product Information GFK-1512M IC693CPU350 D

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.

UPS Ground shipping is always FREE!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PDF Electric & Supply 3-year warranty.

UPS Ground shipping is always FREE!

What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Electric & Supply packaging and includes a PDF Electric & Supply 3 Year Warranty.

UPS Ground shipping is always FREE!

What is Reconditioned?

Reconditioned products from PDF Electric & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.

Our Reconditioned Products always come with a PDF Electric & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!

Repair Service

3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.