GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

IC693CPU350 Image


Same Day - Free Shipping

  • Manufacturer: GE-IP
  • Description: GE Fanuc CPU 350 Module (32K Bytes user memory, 4K I/O, 8 Racks), no built-in Serial Ports .22msec/PROCESSOR (32K Bytes user memory, 4K I/O, 8 Racks)
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693CPU350 : -AA, -BA, -BB, -BC, -BD, -BE, -CE, -CF, -CG, -DH, -DJ, -EJ,

Product Manual Excerpt

IMPORTANT PRODUCT INFORMATION READ THIS INFORMATION FIRST Product: IC693 CPU Modules IC693CPU350-CF with Firmware Release 10.50 IC693CPU360-CG with Firmware Release 10.51 Introduction This document contains information that is not available in any other publication; therefore, we recommend you save it for future reference. This document discusses firmware release 10.51 for CPU360, which corrects the problem noted in the section Problems Resolved by this Release. No new features are added by this release. CPU350 remains at release 10.50 at this time. This document also contains information about several previous releases. Feature Highlights of Firmware Release 10.51 No new features. Feature Highlights of Firmware Release 10.50 No new features. Feature Highlights of Firmware Release 10.00 Note: The following CPU features require the use of VersaPro 1.1 (or later version). For details on these features, please see the VersaPro on-line help. Support was added for the IC693DSM314 servo module. Support was added for storing Local Logic Programs. These programs are stored to the CPU from the programmer These programs will automatically be stored from the CPU to the appropriate smart option module. The limit on the size of all Local Logic Programs is 65280 bytes. Reboot after Fatal Fault If activated, this feature enables the IC693 PLC system to automatically resume normal operation after a fatal fault has occurred. Following the fatal fault, the PLC will automatically reset and resume execution. If fatal faults are present following the power up, the PLC will still be allowed to transition to run mode. The user can enable this feature through a configuration parameter, and can identify the maximum number of retries and the time period these retries may occur within through new Service Request #48. New Service Request 49 may then be used to determine the number of fatal faults and retries that have occurred. Addition of the Drum Sequencer function block. This function block operates in the same manner as on the IC200 CPU. Feature Highlights of Firmware Release 9.00 The following features were introduced in release 9.00. Software Floating-Point. The CPU350 and CPU360 support all of the floating-point function blocks that are currently supported by the CPU352. They are implemented in firmware using floating point emulation. These Floating-Point math function blocks are described in the IC693 PLC Reference Manual. 2 Important Product Information GFK-1512K CPU360 user memory increased to 240K bytes. %R, %AI, and %AQ references are configurable up to 16K of %R, 8K of %AI and 8K of %AQ memory using the MS-DOS PLC programming software, version 9.02. These three references are configurable up to 32K version 2.2 of the Windows PLC programming software and version 1.0 of the VersaPro programming software. Configuration instructions for this feature are described in the MSDOS IC693 Programming Software User s Manual, and are included in on-line help in both Windows PLC programming software packages. Note that the CPU350 does not support configurable user memory. Its user memory is set at a fixed value of 32K bytes. Sequential Event Recorder. The Sequential Event Recorder function block can be used to record up to 1024 samples of 32 individual discrete (bit) references. Both of these CPUs support this function block. Instructions on programming the Sequential Event Recorder are found in the IC693 PLC Reference Manual. Break-free SNP. The SNP protocol no longer requires a break to operate. This allows SNP to work over a wider variety of modems. Hardware Identification The following table shows the revision level of the circuit boards used in the current version of these CPUs. CPU Catalog Number Circuit Board ID Circuit Board Version IC693CPU350-CF CX3A1 44A739579-G01R07 or later IC693CPU360-CG CX3A1 44A739579-G01R07 or later Firmware Upgrade Kits If you wish to upgrade an existing CPU350 or CPU360 to firmware version 10.00, you may purchase the applicable kit identified in the following table. All previous versions are capable of being upgraded. Firmware Upgrade Kit Catalog Numbers CPU Catalog Number Firmware Upgrade Kit Catalog Numbers IC693CPU350-(all versions) 44A747145-G05 IC693CPU360-(all versions) 44A747148-G06 Firmware Identification CPU Catalog Number Motherboard Firmware Version Daughterboard Firmware Version IC693CPU350-CF Main: R10.50 (35A1) Boot: R9.00 (33A1) N/A IC693CPU360-CG Main: R10.51 (16A1) Boot: R9.00 (33A1) N/A

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.

UPS Ground shipping is always FREE!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PDF Electric & Supply 3-year warranty.

UPS Ground shipping is always FREE!

What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PDF Electric & Supply packaging and includes a PDF Electric & Supply 3 Year Warranty.

UPS Ground shipping is always FREE!

What is Reconditioned?

Reconditioned products from PDF Electric & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.

Our Reconditioned Products always come with a PDF Electric & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!

Repair Service

3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.