GE-IP | 9030 | GE Fanuc 90-30 GE-IP PLC

IC693ALG222 Image


IC693ALG222 Lowest Price Guarantee! Image

Same Day - Free Shipping

  • Manufacturer: GE-IP
  • Description: GE Fanuc Series 90-30 12 bit res Analog Input Voltage 16 Single/8 Differential Channels
  • Weight: 1 lbs :: ≈ 1 kgs
  • Warranty: 1 Years
  • Product Revisions Available:
  • Other Available Revisions of the IC693ALG222 : A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z, -HB, -GA, -FA,

Product Manual Excerpt

Analog Voltage Input - 16 Channel IC693ALG222 The 16-Channel Analog Voltage Input module provides up to 16 single-ended or eight differential input channels, each capable of converting an analog input signal to a digital value for use as required by your application. This module provides two input ranges: 0 to 10 V (unipolar) 10 to +10 V (bipolar) Voltage Ranges and Input Modes The default input mode and range is single-ended, unipolar, with the user data scaled so that 0 volts corresponds to a count of 0 and 10 volts corresponds to a count of +32000. The other range and mode are selected by changing the configuration parameters using the Logicmaster 90-30/20/Micro or CIMPLICITY Control configurator software, or the Hand-Held Programmer. The range can be configured for bipolar 10 to +10 V where 10 V corresponds to a count of 32000, 0 V corresponds to a count of 0, and +10 V corresponds to a count of +32000. High and Low alarm limits are available on all ranges. Ranges can be configured on a per channel basis. Power Requirements and LEDs This module consumes a maximum of 112 mA from the 5V bus on the PLC backplane. It also requires a maximum of 41 mA from the backplane Isolated+24 Volt DC supply to power the on-board power converter that provides isolated 5V supplies to power the user-side circuitry (see Table 3-9, Specifications). There are two green LED indicators on the module which provide module and user supply status. The top LED, MODULE OK provides module status information on power-up as follows: ON: status is OK, module configured OFF: no backplane power or software not running (watchdog timer timed out) Continuous rapid flashing: configuration data not received from CPU Slow flashes, then OFF: failed power-up diagnostics or encountered code execution error The bottom LED, Power Supply OK, indicates that the internally generated user-side +5V supply is above a minimum designated level. Location in System This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC system. References Used The number of 16-Channel Analog Voltage Input modules which may be installed in a system depends on the amount of %AI and %I references available. Each module uses 1 to 16 %AI references (depending on the number of channels enabled) and from 8 to 40 %I references (depending on alarm status configuration). The available %AI references are: 64 with CPUs 311, 313, and 323; 128 with CPU331; 1024 with CPUs 340 and 341; and 2048 with CPUs 350 364. 10 10-10 Series 90-30 PLC I/O Module Specifications July 2000 GFK-0898F The maximum number of 16-Channel Analog Voltage Input modules which may be installed in a system are: 4 in a system using CPUs 311, 313, or 323 8 in a system using CPU331 12 in a system using CPUs 340 or 341 51 in a system using CPUs 350 364 When planning the module configuration for your application you must also consider the load capacity of the installed power supply and the total load requirements of all modules that are installed in the baseplate. Refer to the Series 90-30 Programmable Controller Installation Manual, GFK-0356 for details on power supplies and module load requirements. Table 10-3. Specifications for 16-Channel Analog Voltage Input Module, IC693ALG222 Number of Channels 1 to 16 selectable, single-ended 1 to 8 selectable, differential Input Current Ranges 0V to +10V (unipolar) or 10V to +10V (bipolar); selectable each channel Calibration Factory calibrated to: 2.5 mV per count on 0V to +10V (unipolar) range 5 mV per count on 10 to +10V (bipolar) range Update Rate 6 msec (all 16 single-ended channels) 3 msec (all 8 differential channels) Resolution at 0V to +10V 2.5 mV (1 LSB = 2.5 mV) Resolution at 10V to +10V 5 mV (1 LSB = 5 mV) Absolute Accuracy 0.25% of full scale @ 25 C (77 F) 0.5% of full scale over specified operating temperature range Linearity < 1 LSB Isolation 1500 volts between field side and logic side Common Mode Voltage (Differential) 11V (bipolar range) Cross-Channel Rejection > 80 db from DC to 1 kHz Input Impedance >500K ohms (single-ended mode) >1M ohms (differential mode) Input Filter Response 41 Hz (single-ended mode) 82 Hz (differential mode) Internal Power Consumption 112 mA (maximum) from the backplane +5 VDC bus 41 mA (maximum) from the backplane Isolated +24 VDC supply Refer to Appendix B for product standards and general specifications. The summation of the differential input, common-mode voltage, and noise must not exceed 11 volts when referenced to COM. In the presence of severe RF interference (IEC 801-3, 10V/m), accuracy may be degraded to 5% FS. Analog Input Modules 10 GFK-0898F Chapter 10 Analog Input Modules 10-11 CPU Interface to the IC693ALG 222 Analog Voltage Input Module The Series 90-30 PLC uses the data within the %AI data table to record analog values for use by the programmable controller. This scheme for the 16-Channel Analog Voltage Input module is shown below. More information on the CPU interface to analog modules can be found at the beginning of this chapter. SERIES 90-30 CPU A/D CONVERTER DATA TABLE % AI USER CONNECTIONS ANALOG VOLTAGE INPUT MODULE CHx MICRO PROCESSOR BACKPLANE INTERFACE VLSI OPTO ISOLATION COM CHx (+) CHx+1 CHx ( ) 233K 233K 3300pf 3300pf + + 280K 280K a47042 NOTE: CHx AND CHx+1 INDICATE SINGLE-ENDED MODE; CHx (+) AND CHx ( ) INDICATE DIFFERENTIAL MODE Figure 10-9. 16-Channel Analog Voltage Input Module Block Diagram - IC693ALG222 Placement of A/D Bits within the Data Tables Since converters used in the analog modules are 12-bit converters, not all of the 16 bits in the data tables contain data required for the conversion. A version of the 12 bits is placed within the 16-bit data word corresponding to the analog point (in the %AI table). The Series 90-30 PLC system handles the integration differently for the various analog modules. The CPU does not manipulate the data from the input modules before placing it within the word in the %AI data table. The bits in the %AI data table which were not used in the conversion by the input module are either forced to 0 (zero) by the analog input module. Placement of the 12 data bits from the A/D converter for an analog current input data word for the 16-Channel Analog Voltage Input module in unipolar range is shown below. X D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X MSB LSB X=not converted bits Analog values are scaled over the range of the converter. Factory calibration adjusts the analog value per bit (resolution) to a multiple of full scale (that is, 2.5 mV/bit for unipolar; 5 mV/bit for bipolar). This calibration leaves a normal 12-bit converter with 4000 counts (normally 212 = 4096 counts). The data is then scaled with the 4000 counts over the analog range. For example, the data to the A/D converter for the 16-Channel Analog Voltage Input is scaled as shown below. 10 10-12 Series 90-30 PLC I/O Module Specifications July 2000 GFK-0898F A/D BITS (decimal) VOLTAGE; 0 to 10V RANGE a45717 0 10 0 4000 Figure 10-10. A/D Bits vs. Voltage Input for IC693ALG222

Need To Order A Specific Revision?

Give us a call at 1-800-360-6802 or 1-919-535-3180. We can help you with your Revision specific needs.

UPS Ground shipping is always FREE!

What is New Surplus?

These “New Surplus” units are a great cost saving alternative. This product is in the original manufacturer’s packaging with all sub-assemblies and documentation. Comes with a PLC Distribution Factory & Supply 3-year warranty.

UPS Ground shipping is always FREE!

What is Surplus New?

Surplus New - New unused and includes all sub-assemblies and documentation. Product may ship in manufacturer or PLC Distribution Factory & Supply packaging and includes a PLC Distribution Factory & Supply 3 Year Warranty.

UPS Ground shipping is always FREE!

What is Reconditioned?

Reconditioned products from PLC Distribution Factory & Supply are a cost-effective alternative to new and obsoleted PLC products. Every part is reconditioned down to the circuit board level. All parts are thoroughly inspected and hand-cleaned before being functionally tested in a fully configured system.

Our Reconditioned Products always come with a PLC Distribution Factory & Supply 2-Year Warranty.

UPS Ground shipping is always FREE!


We stand behinds our prices with a 110% price match guarantee. If you buy a part from us and, within seven days of purchase, find that part advertised on an authorized distributors website for less, simply contact us and give us a link to the lower advertised price and we'll refund you 110% of the difference between your purchase price and the advertised lower price. The part must be in-stock for immediate shipment and be in similar condition. All pricing must be displayed without signing in.

Repair Service

3-5 Days for most repairs. 24 hour repair upon request at no extra charge. If part is unrepairable, we will exchange with a working unit or return unrepaired.